CAT 160M2 Motor Grader

Dimensions

Overall Length 29.2 ft in (8898 mm)
Width Over Tires 8.47 ft in (2581 mm)
Wheelbase 20.1 ft in (6126 mm)
Rear Ground Clearance 1.13 ft in (344 mm)
Tandem Axle Wheelbase 5 ft in (1523 mm)
Front Ground Clearance 1.97 ft in (600 mm)
Blade Base 8.39 ft in (2557 mm)
Height To Top Of Isomount Cab 10.79 ft in (3287 mm)

Ripper

Pry-Out Force 258201 lb (117118.1 kg)
Ripping Depth – Maximum 16.8 in (426.8 mm)
Ripper Shank Holders 5
Penetration Force 20443 lb (9272.8 kg)
Machine Length Increase, Beam Raised 40.6 in (1031.3 mm)
Ripper Shank Holder Spacing 21 in (533.4 mm)

Engine Details

Number Of Cylinders 6
Engine Make CAT
Engine Model C9.3 ACERT VHP

Frame

Front Frame Structure – Height 1.1 ft in (320.1 mm)
Front Frame Structure – Width 0.9 ft in (254 mm)

Engine Details

Power Measured @ 2100 rpm
Torque Measured @ 2100 rpm
Net Power Gears 7-8 243 hp (181.3 kw)
Net Torque Gears 7-8 1000 lb ft (1355.9 Nm)
Bore 4.5 in (114.3 mm)
Stroke 5.9 in (149.9 mm)
Emissions U.S. Tier 4 Interim/EU Stage IIIB
Engine Model Cat C9.3 ACERT
Derating Altitude 10000 ft in (3048 m)
Maximum Torque 1000 lb ft (1355.9 Nm)
Base Power (1st Gear) – Net 213 hp (158.9 kw)
Standard Capability 109 degrees
Speed At Rated Power 2,100 rpm
High – Ambient Capability 122 degrees
Base Power (1st Gear) – Net – Metric 216 hp (161.1 kw)
High Ambient – Fan Speed – Maximum 1,550 rpm
High Ambient – Fan Speed – Standard 1,400 rpm
High Ambient – Fan Speed – Minimum 500 rpm
Vhp Plus Range – Net 159-196 kW (213-263 hp)
Vhp Plus Range – Net – Metric 159-196 kW (216-267 hp)

Frame

Circle – Diameter 60.2 in (1529.1 mm)
Drawbar – Height 6 in (152.4 mm)
Front Axle – Height To Center 23.6 in (599.5 mm)
Circle – Blade Beam Thickness 1.6 in (40.7 mm)
Front Axle – Total Oscillation Per Side 32 degrees
Drawbar – Thickness 0.5 in (12.7 mm)
Drawbar – Width 3 in (76.2 mm)
Front-Top/Bottom Plate – Width 12 in (304.8 mm)
Front-Top/Bottom Plate – Thickness 0.9 in (22.1 mm)
Front Axle – Wheel Lean – Left/Right 18 degrees

Engine Details

Vhp Plus – Gear 1f, Net 213 hp (158.9 kw)
Vhp Plus – Gear 2f, Net 223 hp (166.3 kw)
Vhp Plus – Gear 3f, Net 233 hp (173.8 kw)
Vhp Plus – Gear 4f, Net 243 hp (181.3 kw)
Vhp Plus – Gear 5f, Net 248 hp (185 kw)
Vhp Plus – Gear 6f, Net 253 hp (188.7 kw)
Vhp Plus – Gear 7f, Net 258 hp (192.4 kw)
Vhp Plus – Gear 8f, Net 263 hp (196.2 kw)
Base Power (All Gears) – Net 213 hp (158.9 kw)

Operational Specs

Std Operation Weight – Front Axle 9339 lb (4236.1 kg)
Hydraulic System Fluid Capacity 26.4 gal (100 L)
Std Operation Weight – Rear Axle 28792 lb (13059.9 kg)
Std Operation Weight – Total 38131 lb (17296 kg)
Max Operation Weight – Front Axle 13343 lb (6052.3 kg)
Max Operation Weight – Rear Axle 36444 lb (16530.8 kg)
Max Operation Weight – Total 52795 lb (23947.5 kg)
Oil System Fluid Capacity 7.9 gal (30 L)
Fuel Tank Capacity 110 gal (416.4 L)
Cooling System Fluid Capacity 14.8 gal (56.1 L)
Transmission Fluid Capacity 17.2 gal (65.2 L)
Circle Gearbox Fluid Capacity 1.8 gal (6.9 L)
Tandem Case Fluid Capacity (Each) 16.9 gal (64 L)
Operating Voltage 24 V
Alternator Supplied Amperage 150 amps

Power Train

Brakes – Parking Multiple Oil Disc
Brakes – Service Multiple Oil Disc
Transmission Direct Drive Powershift
Forward/Reverse Gears 8 Fwd/6 Rev
Brakes – Secondary Dual Circuit Control
Brakes – Service – Surface Area 3565 in2 (2.3 m2)

Steering

Articulation Angle 20 degrees
Turning Radius 25.5 ft in (7.8 m)

Transmission

Transmission Type Direct Drive, Powershift
Number Of Gears – Forward 8
Number Of Gears – Reverse 6
Max Speed – Forward 29 mph (46.7 km/h)
Max Speed – Reverse 22.9 mph (36.9 km/h)

Front Axle

Wheel Lean 18 degrees
Oscillation – Total 32 degrees
Ground Clearance 2 ft in (600 mm)

Weights

Operating Weight – Typically Equipped 45283 lb (20540.1 kg)
Gross Vehicle Weight – Base – Total 38790 lb (17594.9 kg)
Gross Vehicle Weight – Maximum – Total 54869 lb (24888.2 kg)
Operating Weight – Typically Equipped – Total 45283 lb (20540.1 kg)
Gross Vehicle Weight – Base – Rear Axle 28786 lb (13057.2 kg)
Operating Weight – Typically Equipped – Front Axle 13171 lb (5974.3 kg)
Operating Weight – Typically Equipped – Rear Axle 32112 lb (14565.8 kg)
Gross Vehicle Weight – Base – Front Axle 10004 lb (4537.8 kg)
Gross Vehicle Weight – Maximum – Front Axle 17009 lb (7715.2 kg)
Gross Vehicle Weight – Maximum – Rear Axle 37860 lb (17173.1 kg)

Hydraulic System

Standby Pressure 609 psi
Maximum System Pressure 3503 psi

Moldboard

Moldboard Width 14 ft in (4267.2 mm)
Moldboard Height 24 in (609.6 mm)
Moldboard Thickness 0.9 in (22 mm)
Max Depth Of Cut 29.6 in (750 mm)
Side Shift Left 20.1 in (510 mm)
Side Shift Right 26 in (660 mm)
Blade Pull At Max Weight 20044 lb (9091.9 kg)
Blade Down Pressure 22884 lb (10380.1 kg)

Hydraulic System

Pump Type Variable Piston
Pump Flow 55.5 gal/min (210.1 L/min)
Relief Valve Pressure 3503 psi (24152.4 kPa)
Circuit Type Parallel
Pump Output 55.5 gal/min
Reservoir Tank Capacity 15.9 gal (60.2 L)

Moldboard

Blade Width 14 ft in (4.3 m)
Arc Radius 16.3 in (414.1 mm)
Throat Clearance 6.5 in (165.1 mm)
Cutting Edge Width 6 in (152.4 mm)
Cutting Edge Thickness 0.6 in (15.3 mm)
End Bit – Width 6 in (152.4 mm)
End Bit – Thickness 0.6 in (15.3 mm)
Moldboard – Height 24 in (609.6 mm)
Moldboard – Thickness 0.9 in (22.1 mm)
Blade Pull – Maximum Gvw 34072 lb (15454.9 kg)
Blade Pull – Base Gvw 25908 lb (11751.7 kg)
Blade Down Pressure – Base Gvw 17171 lb (7788.7 kg)
Blade Down Pressure – Maximum Gvw 29195 lb (13242.7 kg)

Circle

Diameter 60.3 in (1530 mm)
Rotation 360 degrees
Shift Left 27.4 in (695 mm)
Shift Right 28.7 in (728 mm)
Max Reach Outside Tires – Left 82.3 in (2090 mm)
Max Reach Outside Tires – Right 89.7 in (2278 mm)
Max Lift Above Ground 17.8 in (452 mm)
Blade Tip Angle – Front 40 degrees
Blade Tip Angle – Rear 5 degrees

Operating Specifications

Top Speed – Forward 29.5 mph (47.5 km/h)
Top Speed – Reverse 23.3 mph (37.5 km/h)
Turning Radius – Outside Front Tires 25 ft in (7.6 m)
Steering Range – Left/Right 47.5 degrees
Articulation Angle – Left/Right 20 degrees
Forward – 8th 29.5 mph (47.5 km/h)
Forward – 7th 20.3 mph (32.7 km/h)
Forward – 6th 14.7 mph (23.7 km/h)
Forward – 5th 10.8 mph (17.4 km/h)
Forward – 4th 7 mph (11.3 km/h)
Forward – 3rd 5.1 mph (8.3 km/h)
Forward – 2nd 3.5 mph (5.7 km/h)
Forward – 1st 2.6 mph (4.2 km/h)
Reverse – 6th 23.3 mph (37.5 km/h)
Reverse – 5th 16 mph (25.8 km/h)
Reverse – 4th 8.5 mph (13.7 km/h)
Reverse – 3rd 5.5 mph (8.9 km/h)
Reverse – 2nd 3.8 mph (6.2 km/h)
Reverse – 1st 2 mph (3.3 km/h)

Standards

Brakes ISO 3450, ISO 10265
Rops/Fops ISO 3471/ISO 3499
Sound ISO 6394; ISO 6395
Steering ISO 5010

Service Refill

Cooling System 14.8 gal (56.1 L)
Hydraulic System – Total 26.4 gal (100 L)
Engine Oil 7.9 gal (30 L)
Hydraulic System – Tank 16.9 gal (64 L)
Tandem Housing – Each 16.9 gal (64 L)
Circle Drive Housing 1.8 gal (6.9 L)
Front Wheel Spindle Bearing Housing 0.2 gal (0.5 L)
Fuel Tank Capacity 110 gal (416.4 L)
Transmission – Differential – Final Drives 17.2 gal (65.2 L)

Blade Range

Circle Centershift – Right 28.7 in (729 mm)
Circle Centershift – Left 27.4 in (696 mm)
Moldboard Sideshift – Right 26 in (660.4 mm)
Moldboard Sideshift – Left 20.1 in (510.6 mm)
Blade Tip Range – Forward 40 degrees
Blade Tip Range – Backward 5 degrees
Maximum Shoulder Reach Outside Of Tires – Right 89.7 in (2278.4 mm)
Maximum Shoulder Reach Outside Of Tires – Left 82.3 in (2090.5 mm)
Maximum Lift Above Ground 17.8 in (452.2 mm)
Maximum Depth Of Cut 29.5 in (749.3 mm)
Maximum Blade Position Angle 90 degrees

Scarifier

Front, V-Type – Working Width 47.4 in (1204 mm)
Rear – Scarifier Shank Holders 9
Mid, V-Type – Scarifier Shank Holders 11
Front, V-Type, 5 Or 11 Tooth – Working Width 40.6 in (1031.3 mm)
Front, V-Type, 5 Or 11 Tooth – Scarifying Depth, Maximum 18.4 in (467.4 mm)
Front, V-Type, 5 Or 11 Tooth – Scarifier Shank Holders 5/11
Front, V-Type, 5 Or 11 Tooth – Scarifier Shank Holder Spacing 4.6 in (116.9 mm)
Mid, V-Type – Working Width 46.6 in (1183.7 mm)
Mid, V-Type – Scarifying Depth, Maximum 11.5 in (292.1 mm)
Mid, V-Type – Scarifier Shank Holder Spacing 4.6 in (116.9 mm)
Rear – Working Width 84 in (2133.6 mm)
Rear – Scarifying Depth, Maximum 16.8 in (426.8 mm)
Rear – Scarifier Shank Holder Spacing 10.5 in (266.7 mm)
Front, V-Type – Scarifying Depth, Maximum 40.6 in (1031.3 mm)
Front, V-Type – Scarifier Shank Holders 5/11
Front, V-Type – Scarifier Shank Holder Spacing 18.4 in (467.4 mm)
Mid, Straight – Working Width 70.9 in (1800.9 mm)
Mid, Straight – Scarifier Shank Holder Spacing 4.4 in (111.8 mm)
Mid, Straight – Scarifier Shank Holders 17
Mid, Straight – Scarifying Depth, Maximum 12.5 in (317.5 mm)

Tandems

Height 19.9 in (505.5 mm)
Width 8.3 in (210.9 mm)
Sidewall Thickness – Inner 0.7 in (16.1 mm)
Sidewall Thickness – Outer 0.8 in (18.1 mm)
Drive Chain Pitch 2 in (50.8 mm)
Wheel Axle Spacing 60 in (1522.8 mm)
Tandem Oscillation – Front Up 15 degrees
Tandem Oscillation – Front Down 25 degrees
Ask a question